Product Overview and Selection Scope
NB5R5H505N-E is a 5.0 V rated, 5.5 V surge, 5.0 F H-type coin supercapacitor with polarized solder tabs arranged on opposite axial faces.
This device is polarized and its terminal voltage falls during discharge. Verify the ESR step, capacitance tolerance, load profile, leakage, charging current and minimum system voltage in the complete circuit.
Part-Number Construction
The designation is decoded below using the naming table in the supplied specification.
| Segment | Meaning | Value for this product | Engineering note |
|---|---|---|---|
| NB | Series | Coin-type supercapacitor | Identifies the coin-cell product family. |
| 5R5 | Series voltage code | 5.0 V rated / 5.5 V surge | Use 5.0 V for continuous operation; 5.5 V is the surge limit. |
| H | Terminal format | H-type polarized tabs | Confirm the opposite-face terminal geometry and polarity before PCB release. |
| 505 | Capacitance code | 5.0 F | Nominal capacitance before tolerance and ageing margins. |
| N | Tolerance code | Product specification: −20% to +80% | Use 4.0 F as the initial minimum for conservative calculations. |
| E | Variant code | Standard product variant | Confirm the exact ordering code on the controlled specification. |
Electrical Characteristics
Values below are transcribed from the supplied NYFEA specification. Rated operating voltage and surge voltage are separate limits.
| Parameter | Condition | Specified value | Unit |
|---|---|---|---|
| Rated operating voltage | UR | 5.0 | V |
| Surge voltage | Maximum source-specified surge | 5.5 | V |
| Nominal capacitance | C | 5.0 | F |
| General capacitance tolerance | IEC 62391-1 | −20 to +80 | % |
| Controlled capacitance tolerance | Controlled option | −10 to +20 | % |
| Category temperature range | Ambient | −25 to +70 | °C |
| Maximum ESR | 1 kHz, 10 mA, room temperature | 10 | Ω |
| Leakage current | After 24 h at rated voltage | 15 | µA |
Mechanical Dimensions and Polarity
The component uses a polarized H-type coin construction. The solder tabs are attached on opposite axial faces, as shown in the controlled mechanical drawing. Confirm PCB polarity and the full terminal envelope before assembly.
| Dimension | Nominal | Tolerance | Design use |
|---|---|---|---|
| Body diameter | 24.7 mm | +0.3 / −0.1 mm | Main cylindrical envelope |
| Body thickness | 6.0 mm | ±0.3 mm | Axial package depth |
| Terminal-envelope reference | 9.7 mm | +0.3 mm | Use the controlled drawing datum for final PCB clearance |
| Tab width | 3.5 mm | ±0.2 mm | Terminal width shown in the side view |
| Slot width | 1.8 mm | ±0.2 mm | Elongated terminal opening |
| Tab thickness | 0.2 mm | ±0.02 mm | Terminal cross-section |
Reliability and Endurance
| Test | Source condition | Capacitance requirement | ESR requirement |
|---|---|---|---|
| Load life | 5.0 V at +70 ±2 °C for 1000 h | Decrease ≤30% from initial | ≤4 × specified value |
| Temperature cycling | Five cycles: −25 °C → room temperature → +70 °C → room temperature | Decrease ≤30% from initial | ≤3 × specified value |
| Storage life | Source-defined 1000 h condition within −25 to +70 °C | Decrease ≤30% from initial | ≤4 × initial |
| Cycle life | 500,000 constant-current cycles between specified and half-specified voltage at +25 °C | Within ±30% of initial | ≤3 × initial |
Capacitance and ESR Test Methods
For capacitance measurement, charge the device to rated voltage for 30 minutes and discharge it at the prescribed constant current. ESR is measured using the specified 1 kHz AC method.
Hold-Up, Leakage and Energy Calculations
Estimate the usable interval from the allowable voltage window and load current, then subtract the immediate ESR voltage step. For leakage-current testing, fully discharge the device for at least one hour, apply rated voltage, and evaluate the source-specified 24-hour leakage limit.
PCB Mounting, Soldering and Handling
Assembly and environmental conditions directly affect reliability. Apply the following source-specification precautions during layout and process qualification.
If devices are connected in series, implement voltage balancing and obtain NYFEA application guidance. Also validate hole size, lead pitch, cleaning chemistry, polarity inspection and mechanical support before release.
Application Guidance and Design Limitations
The applications below are engineering use cases consistent with a 5.0 V rated, 5.0 F backup component. They are not end-product certification claims.
RTC BackupMaintain timekeeping through a brief loss of the main supply.
Memory RetentionSupport low-power state preservation and orderly data save.
Smart Meter Data SaveProvide a short window for nonvolatile recording after mains loss.
Compact Control NodesBridge short interruptions after validating the source-listed current limit.
Wireless Sensor BackupMaintain low-power state between supply events after circuit validation.The source specification does not claim automotive, medical, functional-safety, life-support or fault-tolerant qualification. Confirm all mandatory standards for the end product.
NB5R5H505N-E Engineering FAQs
What are the rated voltage and nominal capacitance?
The rated operating voltage is 5.0 V, the surge voltage is 5.5 V, and the nominal capacitance is 5.0 F.
What capacitance tolerance is specified?
The product specification states −20% to +80%, corresponding to an initial range of 4.0 F to 9.0 F.
What is the maximum ESR?
The maximum ESR is 10 Ω at 1 kHz and 10 mA at room temperature.
What is the operating temperature range?
The specified operating range is −25 °C to +70 °C.
What are the package dimensions and terminal arrangement?
The source drawing specifies an approximately Ø24.7 mm body with 6.0 ±0.3 mm thickness. The H-type solder tabs are attached on opposite axial faces; use the controlled drawing for the complete footprint.
Is the component polarized?
Yes. Match the negative marking to the PCB polarity before soldering.
Can it be used as a direct battery replacement?
No. A supercapacitor has continuous voltage decay and an ESR-related voltage step. Validate the load current, minimum system voltage, usable energy and required hold-up time.
What is the difference between rated and surge voltage?
Use 5.0 V as the continuous rated operating voltage. The 5.5 V value is the source-specified surge voltage, not the continuous rating.
Which document controls production decisions?
The supplied NB5R5H505N-E PDF and the current NYFEA-controlled revision remain the design authority.
This page summarizes the supplied NB5R5H505N-E product specification for component evaluation.
